Easy Steps In Reflow Soldering Oven
A lot of people now wonder how it could be made possible. It is not very easy if you are a kind of person who is resourceful. This article aims to help you. There are instructions below you could follow on how to do it. You need all the equipment for you to start. Otherwise you cannot start doing them without the necessary stuff you need.
Put them in one place together. And have a copy of the instructions so you it will not be very difficult. Get a piece of paper if you have not tried this before. And make sure that you follow everything and the way they instruct you to do it. It is necessary so you will be successful in doing the Reflow soldering oven. Do not invent something if you have no enough basis for it. To avoid accident.
Get ready with the thermometer and a timer. Do not rely on the one that is found in the oven. You are required to get one. No need to get the best quality. Just the one you can use and will give accurate results. You can also use them in other projects. What matters most is they work great.
You can now creates a motherboard. Just ensure the size of your board will fit into your oven. Measure the size and then that would be the size you should be using.This is the floor plan. And everything you need to test must be put in here. So be careful in making them. And check if all components are complete.
Add flux. This is used for modification purposes. And it can also be used as a marker So it would be easy to identify the things you put in there. So all the balls will stay in their designated location. Only apply the flux on top of the board and not to somewhere else.
Align the components. You need to do this, so it will be easy for you to recognize them and identify all the parts. And put them inside the oven. Make sure that you can clearly see the activities inside so you can monitor them. If you have a silk screen, use it for the alignment. It is the advise of most experts.
Start them cooking. Just ensure they fit inside. After you put them inside. Close the door of the toaster. You can now cook them for 20 minutes. Just use the timer and thermometer from outside so it will be easy for you. No need to use the temperature of your oven. And see the changes from outside. Do not leave them. You have to watch them until it is done. And make sure to turn them off right away after use.
Let them cool. If the time is over, then open the door. So they will cool faster. This is the only way for you to cool them down. Never touch anything on the surface especially the components. Since they are still in liquid state. If you notice the temperature that it is already 50 degree Celsius, then it is a sign to take them out.
Check them after. Inspect all the components. And see if it successful. And all the they are all connected together. The way, that you wanted them to be.
Put them in one place together. And have a copy of the instructions so you it will not be very difficult. Get a piece of paper if you have not tried this before. And make sure that you follow everything and the way they instruct you to do it. It is necessary so you will be successful in doing the Reflow soldering oven. Do not invent something if you have no enough basis for it. To avoid accident.
Get ready with the thermometer and a timer. Do not rely on the one that is found in the oven. You are required to get one. No need to get the best quality. Just the one you can use and will give accurate results. You can also use them in other projects. What matters most is they work great.
You can now creates a motherboard. Just ensure the size of your board will fit into your oven. Measure the size and then that would be the size you should be using.This is the floor plan. And everything you need to test must be put in here. So be careful in making them. And check if all components are complete.
Add flux. This is used for modification purposes. And it can also be used as a marker So it would be easy to identify the things you put in there. So all the balls will stay in their designated location. Only apply the flux on top of the board and not to somewhere else.
Align the components. You need to do this, so it will be easy for you to recognize them and identify all the parts. And put them inside the oven. Make sure that you can clearly see the activities inside so you can monitor them. If you have a silk screen, use it for the alignment. It is the advise of most experts.
Start them cooking. Just ensure they fit inside. After you put them inside. Close the door of the toaster. You can now cook them for 20 minutes. Just use the timer and thermometer from outside so it will be easy for you. No need to use the temperature of your oven. And see the changes from outside. Do not leave them. You have to watch them until it is done. And make sure to turn them off right away after use.
Let them cool. If the time is over, then open the door. So they will cool faster. This is the only way for you to cool them down. Never touch anything on the surface especially the components. Since they are still in liquid state. If you notice the temperature that it is already 50 degree Celsius, then it is a sign to take them out.
Check them after. Inspect all the components. And see if it successful. And all the they are all connected together. The way, that you wanted them to be.
About the Author:
When you are searching for the facts about a reflow soldering oven, go to our website today. More details can be seen at http://www.sikama.com now.
0 comments:
Post a Comment